氣密性檢測裝置氣體互換工作流程

氣密性檢測裝置氮氣互換工作:首先我們要做的是清洗氣瓶的表明，接著氣體瓶子通過上瓶架慢慢升到輸送線位置并平移到氮氣位置。

Nitrogen gas tightness detection device swap work: first of all we have to do is to show that the cleaning cylinder, gas bottle through the bottle on the shelf and then slowly rise to conveying line position and moving to the nitrogen position.

將手把軟管接頭和瓶閥上緊，啟動瓶子閥門。當壓力小于指定值的時候，我們就應該打開排氣閥進行氣體的排放直到壓力正常。當壓力恢復正常的時候，就可以將排氣閥關閉了。當壓力大于制定的壓力數值的時候，我們得把氣瓶送往殘氣處理站進行必要的處理。

Will handle hose connector and tighten up the bottle bottle valve, valve. When the pressure is less than the specified value, we should open the exhaust valve for gas emissions until pressure is normal. When the pressure returned to normal, can the exhaust valve closed. When the pressure is greater than the set pressure value, we must put the cylinders to residual gas processing station of the necessary processing.

氣密性檢測裝置管路閥啟動，并把氣瓶的氣體全部放出來，再打開氮氣閥，把氮氣放入瓶子里，關掉管路閥;打開排氣閥開始排氣，待氣體壓力進行到正常壓力后將排氣閥關掉;接著啟動氮氣管道閥，把氮氣弄到瓶子里，在關掉氮氣閥;開啟排氣閥，這樣不間斷的放入氮氣，氮氣互換工作完成。

相關文章：氣密性檢測裝置知識你了解多少？

---

當前位置： 首頁 >> 公司動態 >> 行業資訊 發布時間： 2014-09-15
上一篇：  爆破試驗臺控制系統性能決定因素 下一篇： 氣密性檢測裝置檢測方案設計詳解